smartctl 7.5 2025-04-30 r5714 [x86_64-linux-6.12.85-Unraid] (local build)
Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               SEAGATE
Product:              SMKP8000S5xeN7.2
Revision:             3P02
Compliance:           SPC-4
User Capacity:        8,001,563,222,016 bytes [8.00 TB]
Logical block size:   512 bytes
Physical block size:  4096 bytes
LU is fully provisioned
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000c50094c6e9e7
Serial number:        ZA19CGY60000R813PTFV
Device type:          disk
Transport protocol:   SAS (SPL-4)
Local Time is:        Fri May 22 04:13:41 2026 CEST
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Disabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Grown defects during certification = 0
Total blocks reassigned during format = 0
Total new blocks reassigned = 0
Power on minutes since format = 3576
Current Drive Temperature:     43 C
Drive Trip Temperature:        68 C

Manufactured in week 43 of year 2017
Specified cycle count over device lifetime:  10000
Accumulated start-stop cycles:  84
Specified load-unload count over device lifetime:  300000
Accumulated load-unload cycles:  1610
Elements in grown defect list: 0

Vendor (Seagate Cache) information
  Blocks sent to initiator = 2418536080
  Blocks received from initiator = 1987954672
  Blocks read from cache and sent to initiator = 3944288534
  Number of read and write commands whose size <= segment size = 2044657523
  Number of read and write commands whose size > segment size = 13169484

Vendor (Seagate/Hitachi) factory information
  number of hours powered up = 36800.33
  number of minutes until next internal SMART test = 24

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:   1627652037        0         0  1627652037          0     611211.024           0
write:         0        0         0         0          0     255823.167           0
verify: 1788354959        0         0  1788354959          0     236248.671           0

Non-medium error count:      190

SMART Self-test log
Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
     Description                              number   (hours)
# 1  Background short  Completed                   -   36764                 - [-   -    -]

Long (extended) Self-test duration: 47220 seconds [13.1 hours]

Background scan results log
  Status: scan is active
    Accumulated power on time, hours:minutes 36800:20 [2208020 minutes]
    Number of background scans performed: 219,  scan progress: 15.35%
    Number of background medium scans performed: 219
Device does not support General statistics and performance logging

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 0
  number of phys = 1
  phy identifier = 0
    attached device type: SAS or SATA device
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; 6 Gbps
    attached initiator port: ssp=1 stp=1 smp=1
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c50094c6e9e5
    attached SAS address = 0x500605b002bff3e1
    attached phy identifier = 2
    Invalid DWORD count = 4
    Running disparity error count = 4
    Loss of DWORD synchronization count = 8
    Phy reset problem count = 0
relative target port id = 2
  generation code = 0
  number of phys = 1
  phy identifier = 1
    attached device type: no device attached
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; unknown
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c50094c6e9e6
    attached SAS address = 0x0
    attached phy identifier = 0
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization count = 4
    Phy reset problem count = 0

